Ingersoll-rand PH30F-XXX-XXX-C Bedienungsanleitung PDF herunterladen

OPERATOR’S MANUAL

PH30F-XXX-XXX-C

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

RELEASED: 5-28-08

REVISED: 1

0-19-11

(REV. 0

5)

3" DIAPHRAGM PUMP

2:1 RATIO (METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

Figure 1

SERVICE KITS

Refer to Model Description Chart to match the pump mate-

rial options.

637441-XX for  uid section repair (see page 4). NOTE: This kit

also contains several air motor seals which will need to be

replaced.

637369 for air section repair (see page 6).

637374-6 major air valve assembly (see page 7).

PUMP DATA

Models . . . . . . . . . . . see Model Description Chart for “-XXX”

Pump Type . . . . . . . Metallic Air Operated Double Diaphragm

Material . . . . . . . . . . see Model Description Chart

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 lbs (121.6 kgs)

Maximum Air Inlet Pressure . . . . . . . 100 p.s.i.g. (6.9 bar)

Maximum Material Inlet Pressure . . 10 p.s.i.g. (0.69 bar)

Maximum Outlet Pressure . . . . . . . . . 200 p.s.i.g. (13.8 bar)

Maximum Flow Rate . . . . . . . . . . . . . . . 150 g.p.m. (567.8 l.p.m.)

 ooded inlet . . . . . . . . . . . 160 g.p.m. (605.6 l.p.m.)

Displacement / Cycle @ 100 p.s.i.g. 1.4 gal. (5.3 lit.)

Maximum Particle Size . . . . . . . . . . . . 3/8” dia. (9.5 mm)

Maximum Temperature Limits (diaphragm / ball / seal

material)

E.P.R. / EPDM . . . . . . . . . . . . . . -60° to 280° F (-51° to 138° C)

Hytrel® . . . . . . . . . . . . . . . . . . . -20° to 150° F (-29° to 66° C)

Nitrile . . . . . . . . . . . . . . . . . . . . 10° to 180° F (-12° to 82° C)

Polypropylene . . . . . . . . . . . . 35° to 175° F (2° to 79° C)

Santoprene® . . . . . . . . . . . . . . -40° to 225° F (-40° to 107° C)

PTFE. . . . . . . . . . . . . . . . . . . . . . 40° to 225° F (4° to 107° C)

Viton® . . . . . . . . . . . . . . . . . . . . -40° to 350° F (-40° to 177° C)

Dimensional Data . . . . . . . . . . . . . . . . . . see page 8

Noise Level @ 70 p.s.i., 50 c.p.m.

c

. . 83.0 db(A)

d

c

Tested with 67263 mu er assembly installed.

d

The pump sound pressure levels published here have been updated to

an Equivalent Continuous Sound Level (L

Aeq

) to meet the intent of ANSI

S1.13-1971, CAGI-PNEUROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain

combinations may not be recommended, consult a representative or

the factory if you have questions concerning availability.

MODEL DESCRIPTION CHART

PH30F - X S P - S X X - C

Air Motor / Air Cap Material

F - Conductive Polypropylene

/ Stainless Steel

Fluid Connection

A - 3 - 8 N.P.T.F. - 1

B - Rp 3 (3 - 11 BSP parallel)

Ball Material

A - Santoprene T - PTFE

C - Hytrel V - Viton

Fluid Section Service Kit Selection

EXAMPLE: Model #PH30F-AS

P-SAA-C

Fluid Section Service Kit # 637441-AA

PH30F - ASP - S X X - C

Ball Diaphragm

637441 - X X

Diaphragm Material

A - Santoprene T - PTFE / Santoprene

C - Hytrel

Seat Material

S - Stainless Steel

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET – BRYAN, OHIO 43506

(800) 495-0276 FAX(800) 892-6276

© 2010 CCN 15307648

www.ingersollrandproducts.com

Fluid Cap & Manifold Material

S - Stainless Steel

Hardware Material

P - Plated Steel

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - PH30F-XXX-XXX-C

OPERATOR’S MANUAL PH30F-XXX-XXX-CINCLUDING: OPERATION, INSTALLATION & MAINTENANCERELEASED: 5-28-08REVISED: 10-19-11(REV. 05)3" DIAPHRAGM PUM

Seite 2 - HAZARDOUS PRESSURE

Page 2 of 8 PH30F-XXX-XXX-C (en)WARNING EXCESSIVE AIR PRESSURE. Can cause per-sonal injury, pump damage or property damage.Do not exceed the maximum

Seite 3

PH30F-XXX-XXX-C (en) Page 3 of 8y Hytrel® and Viton® are registered trademarks of the DuPont Company y Loctite® and 242® are registered trademarks of

Seite 4 - MATERIAL CODE

Page 4 of 8 PH30F-XXX-XXX-C (en)PARTS LIST / PH30F-XXX-XXX-C FLUID SECTIONc 637441-XX Fluid Section Service Kits include: Balls (see Ball Option, ref

Seite 5 - (Santoprene)

PH30F-XXX-XXX-C (en) Page 5 of 8) ASSEMBLY TORQUE REQUIREMENTS (NOTE: DO NOT OVERTIGHTEN FASTENERS.ALL FASTENERS ARE METRIC.(14) Cap screw, 65 - 70 f

Seite 6

Page 6 of 8 PH30F-XXX-XXX-C (en)PARTS LIST / PH30F-XXX-XXX-C AIR SECTIONd Indicates parts included in 637369 air section service kit shown below and

Seite 7 - MAJOR VALVE

PH30F-XXX-XXX-C (en) Page 7 of 8PARTS LIST / PH30F-XXX-XXX-C AIR SECTION) ASSEMBLY TORQUE REQUIREMENTS (NOTE: DO NOT OVERTIGHTEN FASTENERS.ALL FASTEN

Seite 8 - DIMENSIONAL DATA

Page 8 of 8 PH30F-XXX-XXX-C (en)PN 97999-1381TROUBLE SHOOTINGProduct discharged from exhaust outlet.Check for diaphragm rupture.Check tightness of (1

Kommentare zu diesen Handbüchern

Keine Kommentare