Ingersoll Rand P1IU-A9 Gebrauchs- und Pflegehandbuch PDF herunterladen (Seite 2)

SPECIFICATIONS

Motor Si

ngle-Phase, Induction Motor

Power Source Single-Phase, 120V AC 60 Hz

Current 15.0 A

Tank Capacity 4 gal. (15.1 l)

Maximum Pressure 135 PSI (9.3 bar)

Free Air Delivery

Lubrication Oil

PREPARATION FOR USE

SELECT

ING A LOCATION___________________________

GENERAL. Select a clean, dry, well-lighted area with plenty of

space for proper cooling air flow and accessibility. Locate the unit

on a solid level surface at least 12 inches (30 cm) from walls.

Ensure unit is as level as possible. In order to avoid damaging

the air compressor, do not incline the unit transversely or

longitudinally more than 10°.

TEMPERATURE. Ideal operating temperatures are between

50°F and 100°F (10°C and 37.8°C).

•

CAUTIO

Never operate in temperatures below 32°F

(0°C)orabove104°F(40.0°C).

HUMID AREAS. In frequently humid areas, moisture may form in

the compressor and produce sludge in the lubricant, causing

running parts to wear out prematurely. Excessive moisture is

especially likely to occur if the unit is located in an unheated area

that is subject to large temperature changes. Two signs of

excessive humidity are external condensation on the compressor

when it cools down and a “milky” appearance in petroleum

compressor lubricant. You may be able to prevent moisture from

forming in the compressor by increasing ventilation or operating

for longer intervals.

ATTACHMENTS ___________________________________

When attaching tools and accessories to your air compressor,

dhere to the following general guidelines. Contact customer

service for more information.

•

CAUTIO

If you will be using Ingersoll Rand “All-Season

Select” synthetic lubricant, all downstream

attachments must be compatible. Refer to the

following material compatibility list. If there are

incompatible materials present, or if there are

materials not included in the list, contact

customerservice.

Suitable:

Viton®, Teflon®, Epoxy (Glass Filled), Oil Resistant Alkyd,

Fluorosilicone, Fluorocarbon, Polysulfide, 2-Component Urethane,

Nylon, Delrin®, Celcon®, High Nitrile Rubber (Buna N. NBR more than

36% Acrylonitrile), Polyurethane, Polyethylene, Epichlorohydrin,

Polyacrylate, Melamine, Polypropylene, Baked Phenolics, Epoxy,

Modified Alkyds

(® indicates trademark of DuPont Corporation)

NotRecommended:

Neoprene, Natural Rubber, SBR Rubber, Acrylic Paint, Lacquer, Varnish,

Polystyrene, PVC, ABS, Polycarbonate, Cellulose Acetate, Low Nitrile

Rubber (Buna N. NBR less than 36% Acrylonitrile), EPDM, Ethylene

Vinyl Acetate, Latex, EPR, Acrylics, Phenoxy, Polysulfones, Styrene

Acrylonitrile (San), Butyl

GENERAL REQUIREMENTS. The att

achments, piping, fittings,

receiver tank, etc. must be certified safe for at least the

maximum working pressure of the unit. Use hard-welded or

threaded steel or copper pipes, cast iron fittings and hoses that

are certified safe for the unit’s discharge pressure and

temperature. DO NOT USE PVC PLASTIC. Use pipe thread

sealant on all threads, and make up joints tightly to prevent air

leaks.

CONDENSATE DISCHARGE. Condensate must be disposed of

in accordance with local, state, and federal laws and regulations.

NOTE All com

pressed air systems generate

condensate which accumulates in any drain

point (e.g. tanks, filters, drip legs, aftercoolers,

dryers). This condensate contains lubricating

A TANK PRESSURE GAUGE

B LINE P

RESSURE GAUGE

C TANK

D RUBBER BUMPER

E SAFETY / RELIEF VALVE

F ON/OFF SWITCH

G MOTOR/PUMP

H INTAKE FILTER

I CYLINDER

J OIL DIPSTICK

K CASING COVER

L OIL DRAIN CAP

M TANK DRAIN

N PRESSURE REGULATOR KNOB

O QUICK CONNECT

P LIFTING HANDLE

http://air.ingersollrand.com

P1IU-A9

@ 90 PSI (6.2 bar) 4.3 CFM (125 l/min)

@ 135 PSI (9.3 bar) 3.2 CFM (90 l/min)

1 2 3 4 5 6 7 ... 31 32

Kommentare zu diesen Handbüchern

Keine Kommentare

Ingersoll Rand P1IU-A9 Gebrauchs- und Pflegehandbuch Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Luftkompressoren Ingersoll Rand P1IU-A9